Added

• analogsensor types: NTC and RGB-Led
• Flag for HMC310 #2465
• boiler auxheatersource #2489
• thermostat last error for RC100/300 #2501
• boiler 0xC6 telegram #1963
• CS6800i changes #2448, #2449
• charging pump #2544
• hybrid CSH5800iG #2569
• added EMS Device details to Home Assistant MQTT Discovery
• disinfection command #2601
• added new board profile for upcoming BBQKees E32V2.2
• set differential pressure entity in Mixer device
• set set climate action cooling/heating in HA #2583
• Internal sensors of E32V2_2
• FW200 display options #2610
• CR11 mode settings OFF/MANUAL depends on selTemp #2437
• implemented eFuse settings for BBQKees boards to store model type and ESP chipset
• Analogsensors for pulse output #2624
• Analogsensors frequency input #2631
• SRC plus thermostats #2636
• Greenstar 2000 #2645
• RC3xx dhw modetype #2659
• new boiler entities VR0,VR1, compressor speed #2669
• solar temperature TS16 #2690
• pumpmode enum for HT3 boilers, add commands for manual defrost, chimneysweeper #2727
• pid settings #2735
• refresh MQTT button added to MQTT Settings page
• heating assistance, rounding custum settings #2763
• added counter 0..2 for short pulses, high frequency #2758
• added LWT (Last Will and Testament) to MQTT entities in Home Assistant
• added api/metrics endpoint for prometheus integration by @gr3enk #2774
• added RTL8201 to eth phy list #2800
• added partitions to Web UI Version page, so previous firmware versions can be installed #2837
• button pressures show LED. On a long press (10 seconds) the LED flashes for 5 seconds to indicate a factory reset is about to happen. #2848
• added txpause command to pause the TX, by setting Txmode to 0 (disabled) #2850

Fixed

• dhw/switchtime #2490
• switch to secure mqtt #2492
• update link buttons #2497
• refresh scheduler states #2502
• also rebuild HA config on mqtt connect for scheduler, custom and shower
• FB100 controls the hc, not the master #2510
• IPM DHW module, #2524
• charge optimization #2543
• shower active state retained, shows correctly in HA
• MQTT Command Topic with slashes #2571
• Add pulsed water meter input to V1.3 gateway with Lilygo S3 #2550
• fix missing long 10-second press of Button to perform a factory reset
• fix wwMaxPower on Junkers ZBS14 #2609
• ventilation bypass state from telegram 0x55C #1197
• set selflowtemp for ems+ boilers #2641
• syslog timestamp #2704
• fixed FS format command #2720
• dhw priority setting to boiler and mixer, telegrams 0x2CC, 0x2CD, etc.
• check for valid GPIOs when board profile is changed #2841

Changed

• show console log with ISO date/time #2533
• removed ESP32 CPU temperature
• updated core libraries like AsyncTCP, AsyncWebServer and Modbus
• remove command scan deep
• ignore repeated forceheatingoff commands #2641
• optimized web for better performance by adding lazy loading and caching
• internal system analog sensors (core_voltage, supply_voltage and gateway_temperature) cannot be accidentally removed
• double click button reconnects EMS-ESP to AP
• place system message command in side scheduler loop to reduce stack memory usage by 2KB
• syslog mark interval set to 1 hour
• handle process_telegram in oneloop
• improved GPIO validation for Analog Sensors and System GPIOs
• entities with no values are greyed out in the Web UI in the Customization page
• added System Status to Web Status page
• show number on entities and supported languages in log on boot
• on tx read fail delay the 3rd. retry 2 sec
• move vectors and lists to PSRAM
• removed unused last topic/payload echo-check
• added Home Assistant device details to MQTT Discovery for all devices
• device_class and state_class changes for HA MQTT Discovery #2825